LIN INDUSTRY CO., LIMITED
  • HOME
    • ABOUT US
    • NEWS
  • PRODUCTS
    • Silicone Rubber
    • Membrane Keypad
    • Plastic Injection
    • Light Guide Film
    • Metal Injection-MIM
    • Printed Circuit
    • METAL LABEL
  • Quality System
  • Material Certificate
  • FAQ
  • CONTACT

Medical use keypad, parts
How does the metal dome work?
What is the resistance difference between a golden pill V.S. a c...
Which is more stable? Carbon pill or Pinted conductive ink?
Spring Loaded Connector(pogo pin connector)
内容编辑 内容编辑
★PLASTIC INJECTION MOLDING
分类: PLASTIC INJECTION MOLDING  发布时间: 2003-11-05 00:00 

★PLASTIC INJECTION MOLDING
PLASTIC INJECTION MOLDING

PLASTIC INJECTION MOLDING

Quoting

Once a 3D CAD model is finished, you can specify material, quantity, finish, overall expectation of the part in a notes section, and essentially, communicate as much information about that part as possible. The part will be analyzed based on our manufacturing process to generate a quote. Aslo, you can call a customer service engineer with questions about our process and how it relates to your part geometry and make any modifications that are needed.

When you’re satisfied with your design and decide to order your part, it moves to the mold designers, where we develop your 3D CAD in its negative image to digitally design two halves of the mold, or the A-Side and B-Side. The mold designers create the shutoffs and the parting line — which are custom to your geometry — as well as layout of the gate(s) and ejector pins. The mold design is sent back to you for final approval, and when ready, the necessary toolpathing begins to mill your mold.

Mold production

Our designers toolpath the digital mold design to our CNC machines instructing the end mills where to travel on the X, Y and Z planes, so the machine can rapidly mill both sides of the mold out of an aluminum block. Any pickouts, cams or additional mold features that need to be fitted are also created at this time. Your mold is now in a surface finish stage of F0, or as-milled. The mold moves into our build department where a mold operator is assigned to polish your mold at your desired level of finish. Mold polishing is one of the most detailed and manually intensive processes — one that is almost artistic in nature. All of the ejector pins are cut to length, the A-Side and B-Side are assembled to the press and final fittings are done to ensure the mold will seal properly once resin is injected.
Mold production
plastic injection mold. Protomold milling
Milling
plastic injection molding process. Protomold mold finishing
Mold finishing

Part production

Resin pellets — from either our stocked supply, which may also include a 3-percent salt-and-pepper mix of colorant, or supplied by a customer — are loaded into a barrel where they will eventually be melted, compressed and injected into the mold’s runner system. Hot resin is shot into the mold cavity through the gates, the part is molded, and ejector pins facilitate removal of the part from the mold and into a loading bin. The thermoplastic injection-molding processes is a standard process involving an aluminum mold with no heating or cooling lines running through it, which means cycle times are a bit longer. It allows our molders to monitor fill pressure, cosmetic concerns and the basic quality of the parts, so they are ready to ship upon finishing. When the run is complete, parts (or the initial sample run) are boxed and shipped shortly thereafter.


Surface finish

A number of standard finishes are available for injection-molded parts. Our current finishes include non-cosmetic, low-cosmetic and EDM finishes; bead-blast texturing; and high-end mold polishing.

Standard finishes (from least to most costly):
PM-F0:
Non-cosmetic: finish to Protomold discretion
PM-F1:
Low-cosmetic: most toolmarks removed
PM-F2:
Non-cosmetic: Protomold discretion, EDM finish and/or toolmarks permissible
SPI-C1:
600 grit stone, 10-12 Ra
PM-T1:
Protomold texture, SPI-C1 followed by light bead blast
PM-T2:
Protomold texture, SPI-C1 followed by medium bead blast
SPI-B1:
600 grit paper, 2-3 Ra
SPI-A2:
Grade #2 Diamond Buff, 1-2 Ra
*“PM” in the table signifies a surface finish adjusted to fit the quick-turn injection molding process, where SPI (The Society of the Plastics Industry) denotes an industry-standard finish.


IMD-In Mold Decoration (IML-IMF-IMR) flow-chart


★PLASTIC INJECTION MOLDING ★PLASTIC INJECTION MOLDING

上一产品:没有了
下一产品:没有了
Copyright © 2014-2016, All rights reserved